BPSC Model Paper SST Technical Female Posts

BPSC Model Paper SST Technical Female Posts

SST Technical Model Papers by Balochistan Public Service Commission

Model Paper SST Tech (Female)
Total Marks:100 Time 3 Hours
English Communication skills
Workshop Practice computer
Drawing
Q No 1 Compulsory
1. Communication is derived from Latin Word
a) Community b) command c) communes d) Committees
2. Communication Without Word is called
a) Nonverbal Communication
b) Verbal Communication
c) Oral Communication
d) Written communication
3. Effective communication is that in which
a) Senders sends a complete message
b) Receivers understand the message of sender
c) Communication is oral
d) None of the above
04.The conversion of spoken word into written language is
a) Transplantation
b) Transmission
c)Transcription
d)Translation
05. In English communication Reading means
a) recognition
b) Observing text
c) comprehension
d)recognition and comprehension
06. which of the following is related to Business
a) Marketing
b) Stock exchange
c) Banking
d) All of above
07. ___________ establishes the technical report
a) logical conclusion
b) illogical conclusion
c) personal prejudice
d) misplaced Learning
08. in technical writing the largest report termed as
a) conclusion/recommendation
b) discussion
c) heading
d) footing
09. A report may be used for
a) Reporting
b) Hearing
c) Both A and B
d) none of this
10.A dress code is an Example of _________ communication
a) Verbal
b) Nonverbal
c) written
d) spoken
11.understanding ________ different parts of speech forms the base of learning grammar.
a) Five
b) Eight
c) Six
d) Seven
12.A major challenge in using E mail effectively is to Decide______
And when to manage your Email
a) How to retrieve
b) How to secure
c) How to compose
d) How often
13. The Term Computer is derived from _________?
a) Latin
b) German
c) French
d) Arabic
14. computer is composed of units
a) ALU,CU,Memory unit
b) ALU ,CU
c) Memory Unit
d) Only ALU
15. Mouse is used as a
a) input devices
b) output devices
c) can be used as both input and output
d) None of these
16. which is the commonly used unit for measuring the speed of data transmission?
a) Bits per second
b) Hertz
c)Frequency
d)Mega Hertz
17. The basic operation performed by a computer are
a) Arithmetic Operation
b) Logical Operation
c) Storage and relatives
d) All the above
18.if a Computer has more than one processor then it is known as
a) Uni processor
b) Multiprocessor
c) Multi-threaded
d) Multi programming
19. WWW stands for
a) World wide Web
b) Wide World Web
c)Web Worldwide
d)World Whole Web
20 . The computer that processes both Analog and Digital is called
a) Analog Computer
b) Digital Computer
c) Hybrid computer
d) Main frame computer
22 .CD ROM stands for_______
a) Compactable Read Only Memory
b) compact data read only Memory
c) Compactable Disk read only memory
d)Compact Disk Read Only Memory
23. which one is Digital Device
a) Digital Clock
b) Automobile speed meter
c) clock with a dial and two hand
d) all of them
24. the First computers were programmed using_______
a) Assembly language
b) machine language
c) source code
d) object Code
25. RAM Memory is that which is
a) Volatile
b) Nonvolatile
c) Second name Of Rom
d) Secondary Storage Device

Part B Attempt any three question carry 15 marks
Workshop Practice
a. computer Application
b. Communication Skills

Q NO 1 a) what is operating System?
b). Differentiate between System Software and system hardware?
c). what are the shortcut keys are used to save time give some
Examples and explanation?
Q No 2 a). what is computer system?
b). how software’s are installed in the computer system?
c). Explain the First three generation of computer system?
Q No3 a). Write a short note on scientific report?
b). Explain The communication model?
c). What is the use of 7 C’s in communication?
Q No 4 a). Compare Oral presentation with written Presentation?
b). Differentiate Between Verbal and Non-Verbal Communication?

Part c DRAWING Attempt Any Two Question

Q NO 1 a). What is the concept of Drawing in your Technology?
b). What symbols do you used to draw your required Drawing?
c). Explain the Instruments used in drawing
Q No2 a). which software are used in the Basic Engineering drawing?
b). how Drawing is useful to give a concept to work technically?
c). Explain the tool of drawing Software used in technology?
Q No3 a). which rules used to divide the circle in different angles?
b). how colors differentiate the symbol properties explain any two?
c). what kind of tools are used in workshop explain any two?

Recommended books
1. Computer Application software by NISTE ISLAMABAD
2. Basic Engineering Drawing By NISTE
3. Effective Business Communication By ATA UR REHMAN

BPSC SST Technical Male Sample Papers

BPSC SST Technical Male Sample Papers

Balochistan Public Service Commission SST Tech Past Papers, Sample Papers, Model Papers, Paper Pattern

Model Paper for SST- Tech (Male)
Total Marks : 100 Time: 3 Hours
1. Work Shop Practice
2. Drawing

Q: No. 1. Compulsory 25 Marks

1. Identify the pair which has same dimensions
a. Force & power
b. Energy and work
c. Momentum and energy
d. Impulse and momentum
2. Newton’s first law of motion gives the concept of
a. Work
b. Force
c. Inertia
d. Energy
3. Impulse gives a measure of the produce
a. Force and displacement
b. Force and time
c. Force and velocity
4. According to equilibrium law, two force can be equilibrium only if they are
a. equal in magnitude
b. opposite in direction
c. collinear in action
5. The kinetic energy of a body is stated to increase by 300 percent. The corresponding increase in momentum of the body will be
a. 50
b. 100
c. 200
d. 300 percent
6. The apparent weight of a man in a lift is less then the real weight when the left is going down.
a. Freely
b. under the force of gravity
c. with some constant velocity
d. with some acceleration
7. When a body executes simple harmonic motion, there is always a constant ratio between the displacement of mass and its
a. Frequency
b. Velocity
c. time period
d. acceleration
8. Periodic time of a particle moving with simple harmonic motion is the time taken by the particle for
a. quarter oscillation
b. half oscillation
c. complete oscillation
d. two oscillations
9. The length of a seconds pendulum is
a. 56.3cm
b. 74.8cm
c. 99.4cm
d. 112.5 cm
10. The MOI of a body does not depend upon
a. shape of the body
b. mass of the body and its distribution within the body
c. axis of rotation of the body
d. angular velocity of the body
11. The force of friction between two bodies in contact is
a. function of the relative velocity between them
b. always normal to the surface of contact
c. never shown in the free body diagram of the system of these two bodies
d. dependent on the areas of contact
12. Which one of the following surfaces in contact has minimum coefficient of friction
a. wood on wood
b. steel on steel
c. rubber tyre on dry concrete
d. rubber tyre on wet concrete
13. The deformation per unit length in the direction of load is called
a. lateral strain
b. shear strain
c. linear or longitudinal strain
d. volumetric strain
14. Modulus of elasticity is defined as the ratio of
a. axial stress to lateral strain
b. axial stress to axial strain
c. lateral strain to longitudinal strain
d. axial stress to volumetric strain
15. Which amongst the following substances, is most elastic?
a. Brass
b. Glass
c. Rubber
d. Steel
16. Young’s modulus of elasticity for a perfectly rigid body is
a. Zero
b. Unity
c. Infinity
d. some finite non-zero constant
17. Which of the following is a dimensional quantity?
a. shear stress
b. bulk modulus
c. Poisson’s ratio
d. Strain
18. Percentage elongation during tensile test is indicative of
a. Ductility
b. Malleability
c. Creep
d. fatigue strength
19. Toughness of a material signifies
a. strength
b. softening
c. brittleness
d. fatigue resistance
20. Stiffness of a material is expressed in terms of
a. mass density
b. hardness number
c. modulus of elasticity
d. impact strength
21. The tendency of a material to fracture without appreciable of deformation is called
a. Toughness
b. Stiffness
c. Plasticity
d. Brittleness
22. Lack of toughness in a material implies
a. Brittleness
b. Plasticity
c. Malleability
d. creep strength
23. The statement stress is proportional to strain, i.e., the Hook’s law hold goods upto
a. elastic limit
b. proportional limit
c. upper yield point
d. lower yield point
24. The point on the stress-strain curve at which the cross-sectional area of the test specimen starts decreasing is called the
a. elastic limit
b. proportional limit
c. upper yield point
d. ultimate stress point
25. Percentage elongation during tensile test is indicative of
a. Creep
b. Malleability
c. Ductility
d. elasticity of the metal

Part – B Attempt any 3 Questions. Each Question carry 15 marks
Work Shop Practice
a. Electrical shop
b. Metal shop
c. Welding shop
d. Wood Work shop

Short Questions
Q-1. a. Explain Cable and its types
b. Differentiate between conductor and insulator
c. Explain earthing system

Q.2 a. Differentiate between series and parallel circuit
b. What is ohm law?
c. What is resistance, capacitance and inductance

Q. 3 a. Define the fallowing
Welding. Soldering. Brazing. Forging
b. Describe Arc welding electrodes types.
c. Briefly explain the gas welding gases

Q. 4. a. General safety precautions in wood work shop.
b. Differentiate between hammer and mallet
c. Briefly classify wood types

Q. 5. a. What are the cutting tool types and cutting tool materials?
b. Purpose of using of cutting fluids ?
c. Differentiate between natural and manufactured abrasive

Part- C DRAWING Attempt any 2 Questions

Q.1 a. Which instruments are used mainly in drawing.
b. Describe classification of lines.
c. Briefly explain the use of T- Square and Set Square

Q.2. a. Brief note on procedure of dimensioning
b. Briefly describe ISO system of fits
c. What are the different types of fit.

Q. 3 a. Write note on tolerance
b. Discuss permissible deviation of measurements
c. Briefly describe surface condition and symbols.

Recommended Books
1. Technical Drawing. By G. Schiblee and Sheraz Ali
2. Work Shop practice By NISTE Islam abad
3. Manual on Work Shop practice 1 & 2 By S & T E, ministry of Education. Islamabad
4. Basic engineering Drawing & CAD By NISTE

Balochistan Police Department ASI Assistant Sub Inspector Jobs Through Balochistan Public Service Commission Written Test Syllabus Past Papers

Balochistan Police Department ASI Assistant Sub Inspector Jobs Through Balochistan Public Service Commission Written Test Syllabus Past Papers

BPSC Advertisement No 11-2018

BALOCHISTAN POLICE DEPARTMENT

Twenty two (22) posts of Assistant Sub Inspector (B-09) (MALE/FEMALE)

Local/Domicile:
Local/Domicile of the concerned Region (Balochistan Province) can apply.

Educational Qualification:
Intermediate from any recognized Board of Intermediate and Secondary Education.

Physical Standard for Male:
i. Minimum Hieght = 5’.7”
ii. Chest Measurement = 33” x 341/2
iii. Medically Fit
Note: Those Candidates who do not fulfill the condition of Height/Chest are not Eligible.
Physical Standard for Female:
i. Minimum Height = 5’.3”
ii. Medically Fit
Note: Those candidates who do not fulfill the condition of Height are not eligible.

Age Limit (For Male Candidates):
18 to 25 years on closing date for receipt of
applications.(No age relaxation will be entertained)
Age Limit (For Female Candidates):
18 to 35 years on closing date for receipt of
application.(No age relaxation shall be entertained)

Syllabus Subjective Paper: (i) English Essay (ii) Urdu Essay (iii) General Knowledge (iv) Translation from Urdu to English and English to Urdu
Note: Only those candidates will be called for viva voce test, who qualifies the written exam and fulfill the required physical standard.

CLOSING DATE FOR RECEIPT OF APPLICATIONS IS
(Friday) 30th November, 2018